Technical Service Methodology
Automotive Care, Protection & Restoration
Each service pathway is structured around preliminary condition assessment, surface or component preparation, specialist intervention, quality-control verification and final handover.
The final methodology is determined by the vehicle's existing condition, substrate compatibility, material selection and the scope formally authorised following inspection. Additional work is undertaken only where separately assessed and approved.
Vehicle Care & Reconditioning
Precision Vehicle Detailing & Structured Wash Care
A condition-led exterior and interior care procedure designed around the surfaces, contamination level and areas included within the authorised service scope.
Examine accessible exterior and cabin surfaces, identify sensitive materials and establish the approved treatment boundaries before commencement.
Remove loose contamination and carry out the appropriate wash sequence across the authorised exterior areas, wheels and related surfaces.
Perform focused cleaning according to surface type, followed by controlled drying and interior treatment where included within the selected service.
Review completed areas, address practical omissions and communicate any condition-related limitations identified during the procedure.
Vehicle Care & Reconditioning
Exterior Surface & Cabin Reconditioning
A coordinated reconditioning programme separating exterior and interior materials by substrate type so each area can receive an appropriate preparation and treatment methodology.
Evaluate paintwork, trim, glazing, wheels, upholstery and cabin materials while identifying areas requiring specialised attention.
Clean and prepare the authorised exterior surfaces before proceeding with detailed treatment of paintwork, trim, glazing and wheel areas.
Remove loose debris and treat approved interior surfaces using a procedure selected according to the material and existing condition.
Verify the completed exterior and cabin presentation and identify permanent staining, wear or damage beyond the corrective capability of cleaning alone.
Vehicle Care & Reconditioning
Intensive Interior Reconditioning
A deeper cabin-treatment procedure selected according to upholstery construction, surface condition, contamination level and the interior areas authorised for treatment.
Inspect seating, carpeting, trim panels and other cabin surfaces before determining the appropriate treatment methodology.
Vacuum and remove loose particulate contamination so subsequent treatment can concentrate on embedded or affected areas.
Treat approved fabrics, carpets, plastics and compatible interior materials according to their construction and existing condition.
Allow treated materials to stabilise as required, then inspect the cabin and document visible limitations such as permanent staining, ageing or wear.
Paintwork Correction & Refinement
Machine Polishing & Corrective Paint Refinement
A paintwork-correction methodology established after assessing visible defects, previous repair history and the condition of the existing finish. Correction intensity is selected conservatively according to the surface presented.
Evaluate visible defects, previous refinishing and general surface condition before defining the appropriate correction sequence.
Prepare the paint surface through cleaning and decontamination while protecting sensitive trim, edges and adjoining materials where required.
Establish a suitable correction approach on a controlled test area and undertake the approved polishing stages without assuming every defect can be safely eliminated.
Remove polishing residue, evaluate the finish under suitable lighting and complete the authorised final-refinement stage.
Optical Surface Restoration
Headlamp Lens Restoration & Clarity Refinement
A restoration process directed at correctable exterior lens deterioration after distinguishing external oxidation or surface damage from deterioration located within the lamp assembly.
Inspect haze, oxidation, surface degradation and indications of internal deterioration before treatment is authorised.
Prepare the lens and protect adjacent paintwork and trim before controlled surface refinement begins.
Correct the exterior lens surface through the required staged refinement and polishing procedure.
Evaluate the restored exterior surface while identifying any remaining internal deterioration or severe ageing that cannot be corrected externally.
Wheel Care & Refinishing
Wheel Decontamination & Cosmetic Reconditioning
Wheel treatment begins with an assessment of the existing finish, contamination and visible cosmetic condition before cleaning or any separately authorised restoration procedure.
Inspect the visible coating, contamination and cosmetic damage before selecting an appropriate treatment sequence.
Clean accessible wheel surfaces and remove compatible contamination according to the condition of the existing finish.
Undertake repair or refinishing only where separately assessed and included within the approved project scope.
Review the cleaned or restored wheel finish and complete a final-condition inspection before handover.
Vehicle Protection & Film Systems
Paint Protection Film Application
Protective-film installation is configured around existing paint condition, selected coverage, panel geometry and the areas formally authorised for application.
Evaluate visible paint condition and confirm the panels, coverage boundaries and installation scope before preparation begins.
Clean, decontaminate and prepare installation surfaces; component removal is undertaken only where necessary and authorised.
Position and apply the film across the selected panels while managing alignment, contour conformity and edge finishing according to panel geometry.
Verify visible alignment and edge condition, allow the installation to stabilise and provide relevant initial aftercare guidance.
Vehicle Protection & Film Systems
Colour Paint-Protection Film Transformation
Colour protective-film installation combines paint-surface protection with an aesthetic colour transformation and therefore requires surface-condition, colour and coverage approval before application.
Evaluate the vehicle finish, confirm the selected film colour and establish the panels included within the authorised transformation.
Clean and decontaminate the relevant panels to provide an appropriately prepared surface for installation.
Apply the selected colour film progressively while controlling alignment, contour formation and edge finishing around the approved disassembly scope.
Review panel-to-panel presentation, installation edges and overall finish before vehicle handover.
Vehicle Protection & Film Systems
Vehicle Surface Wrapping & Aesthetic Transformation
Vehicle wrapping is undertaken after assessing paint condition, confirming the selected material and defining the authorised coverage, access and component-removal requirements.
Review the existing surface, selected wrap material and the panels included within the transformation.
Prepare the relevant surfaces thoroughly and remove components only where required and authorised for installation access and edge finishing.
Position, form and finish the wrap across approved panels while managing joins, contours and transition areas.
Inspect visible edge adhesion, panel transitions and overall presentation before final handover.
Automotive Glazing & Thermal-Control Films
Nano-Ceramic Automotive Window-Film Application
Automotive window-film installation begins with glazing and existing-film assessment, followed by controlled glass preparation, film sizing and application.
Inspect visible glass condition and determine whether existing film removal or additional preparation is required.
Protect adjacent cabin areas and prepare the glazing to minimise contamination during installation.
Prepare the film for the selected glazing, position it accurately and complete the controlled installation procedure.
Verify visible edge condition and presentation, then provide guidance relating to the initial stabilisation period.
Automotive Glazing & Thermal-Control Films
Clear Windscreen Thermal-Control Film
Clear windscreen film is applied following an assessment of glazing condition and confirmation of the authorised film system and installation scope.
Inspect the glazing, existing film and visible damage before preparation is undertaken.
Prepare the installation surface carefully while protecting adjacent dashboard and cabin materials.
Prepare the selected film to the windscreen geometry, position it and complete the installation process.
Inspect the completed application and provide appropriate guidance for the initial stabilisation period.
Surface Protection Systems
Ceramic Surface Protection Application
Ceramic coating preparation is determined by existing paint condition. Corrective polishing is undertaken only where separately selected and authorised within the project scope.
Evaluate contamination, visible defects and previous surface work before defining the preparation requirement.
Prepare the paint surface appropriately; corrective refinement is performed only where included within the authorised scope.
Complete the final surface-preparation stage and apply the selected coating according to the applicable product procedure.
Allow the coating to stabilise as required, inspect the application and provide relevant early-stage aftercare guidance.
Film Removal & Surface Recovery
PPF, Vehicle Wrap & Window-Film Deinstallation
Existing protective or decorative film is assessed before removal because material age, adhesive condition, prior refinishing and the substrate underneath can influence the deinstallation process.
Evaluate film age, visible lifting, adhesive condition and known previous surface repairs before removal begins.
Remove the existing material progressively using a method selected for its type and observed condition.
Address compatible adhesive residue and clean the newly exposed surface as required.
Review the underlying paintwork, glass or trim after removal, noting that pre-existing deterioration may become visible only once the film is removed.
Automotive Refinishing & Restoration
Automotive Paint Refinishing
Refinishing methodology is established from panel condition, previous repair history and the authorised repair requirement before preparation, coating application and final finishing.
Inspect the affected panels, visible previous repairs and preparation requirements before refinishing work commences.
Complete authorised surface repair, abrasive preparation and masking before the refinishing stages are undertaken.
Apply the required refinishing stages as applicable to the approved paint system and individual repair scope.
Complete required drying and finishing procedures, inspect the repaired panels and reinstall removed components where applicable.
Automotive Body Repair & Restoration
Bodywork, Corrosion Remediation & Restoration
Body repair is scoped following inspection. The applicable methodology depends on damage type, corrosion condition, panel construction, access requirements and the components involved.
Review visible dents, corrosion, panel condition, alignment and areas requiring access or controlled disassembly.
Remove or protect applicable components where authorised and prepare the affected area for the selected repair procedure.
Undertake the approved dent, metal, corrosion, surface-preparation or refinishing work according to the condition identified.
Reinstall applicable components and review visible alignment, operation and surface presentation before handover.
Vehicle Styling & Customisation
Vehicle Customisation & Component Integration
Customisation projects begin with the intended transformation, vehicle compatibility, component selection and the materials or parts authorised for the work.
Define the requested modification and inspect the vehicle areas affected by the intended work.
Review the selected components, preparation requirements and any associated work necessary before installation.
Undertake the authorised installation or modification while protecting adjoining vehicle surfaces and components.
Inspect component fitment, relevant operation and final aesthetic presentation before vehicle handover.
Request a Technical Inspection or Project Quotation
Provide the vehicle specification, existing condition and intended service scope so preparation requirements, material compatibility and the applicable technical methodology can be evaluated before commencement.
Submit an Automotive Enquiry